Features & Benefits
Fast Dry
Abrasion Resistance
PACRYLIC RL is a modified acrylic-chlorinated rubber solvent-based paint that has excellent resistance to wear and tear for road markings such as edge lines, centerlines, zebra crossing, road curbs, speed humps and many more. It is fast-drying and has excellent outdoor durability and abrasion resistance.
Typical uses: Such as cement, pavement brick, concrete, masonry surfaces, asphalt, Lining/marking of roads, runways, car parks, warehouses, safety areas, and exterior or interior use.
Surface Preparation
Prior application of PAYCRYLIC RL:-
New surface: Surfaces must be sound, clean, dry and free from all defective or poorly adhering material, dirt, grease, etc. Not recommended for fresh asphalt. Test area is recommended before work is commenced.
| Color | Yellow, White, black, refer PAYNT HEAVY DUTY PROTECTIVE COATINGS color cards |
| Film Finish | Matt |
| Drying Time | Touch dry 15 - 20 minutes |
| Recoating Interval | Minimum 50 minutes |
| Theoretical Coverage | Approximately 5 – 7 m² / liter (depends on surface conditions) |
| Coats | 2 Coats |
| Application | Brush, roller, air spray or airless spray |
| Thinner/Cleaner | Use Paynthinner 12 |
Safety, Health and Environment
During painting, make sure no source of ignition at surrounding and no smoking. Always remember to use protective equipment especially eye-goggles and a face mask to cover the mouth and nose. Remember to ensure adequate ventilation in rooms you are painting – open windows and doors wherever possible. In case of contact with eyes, rinse immediately with plenty of water and seek medical treatment. To remove splashes of paint from skin, use suitable cleanser or soap and water. When not in use, store paint in cool and shaded place and do not directly expose sunlight. Do not dispose paint into drains or watercourses. Wash your hands after use.
Refer to PAYNT Technical Data Sheet (TDS) for further details. - click button for pdf
Safety Data Sheet (SDS) is available upon request.
Photo gallery
PAYNTOXY finish is a two-pack polyamide cured epoxy finishing and intermediate coating. It has high content quality pigments produce a continuous paint film after dry and cures through wide temperature range...
PAYNTOXY ANTI-SLIP finish is a two-pack polyamide cured epoxy finishing with an anti-slip agent. It has high content, quality pigments, produces a continuous paint film after drying and cures through a wide temperature range...
PAYNTGUARD 1000 HIGH GLOSS FINISH is a solvent-based alkyd enamel finishing coat. It is formulated to give excellent durability, gloss, and colour retention. It has high content, and quality pigment and produces continuous paint film after drying...
PAYNTGUARD PRIMER is a premium grade single pack modified alkyd resin base, specially formulated for steel primer to act as a corrosion inhibitor before applying top coats.
PAYNTGUARD PROTECTIVE ZINC PHOSPHATE PRIMER is a single pack modified alkyd resin base rust inhibitive primer for priming on iron and steel. It is recommended on iron and steel surfaces under...
PAYNTGUARD PROTECTIVE ZINC PHOSPHATE PRIMER is a single pack modified alkyd resin base rust inhibitive primer for priming on iron and steel. It is recommended on iron and steel surfaces under non-immersion conditions...
PAYNTGUARD PROTECTIVE ZC GREY GREEN PRIMER is a single pack modified alkyd resin base rust inhibitive primer for priming on iron and steel. It is used on iron and steel surfaces under non-immersion conditions...
PACRYLIC PROTECTIVE PRIMER is an acrylic solvent-based sealer. It is formulated to protect the finishing coats against the effect of alkalinity and moisture from the wall...
PAYNTOXY HEAVY DUTY ZINC PHOSPHATE PRIMER is a two-component polyamide cured epoxy primer designed for use as a high-performance primer for many types of metal surfaces...
PAYNTOXY RED OXIDE PRIMER is a two-component polyamide cured epoxy primer designed for use as a high-performance primer for many types of metal surfaces. It is an economical, general-purpose primer for most general industrial...
PAYNTOXY MP PRIMER is a two-pack polyamide cured multipurpose epoxy coating. It gives excellent and corrosion protection. It has high content and quality pigments and produces a continuous paint film after dry....
PAYNTICONE is a silicone heat-resistant paint, a type of coating formulated with silicone resins to provide exceptional heat resistance and durability. This type of paint is designed to withstand high temperatures without losing its adhesion....
PACRYLIC FINISH TOPCOAT is an acrylic resin-based finish paint which has an excellent outdoor durability, abrasion, and weathering resistance suitable for many substrates such as concrete cement, masonry surfaces and metal....
PACRYLIC RL is a modified acrylic-chlorinated rubber solvent-based paint that has excellent resistance to wear and tear for road markings such as edge lines, centerlines, zebra crossing, road curbs, speed humps...
PAYNTGLOSS is a clear aliphatic polyurethane recoat-able finish (Gloss) coating. It is a two-component transparent solvent based polyurethane resin coating and has been formulated to provide a highly durable direct gloss and colour retention topcoat finish...
PAYNTSHIELD ANTI-SLIP Finish is a two-component of coating that contains polyurethane resins with anti-slip agent, that is to be used as topcoat in atmospheric environments. It is formulated to provide a highly durable gloss...
PAYNTSHIELD Polyurethane Recoatable Finish is a two-component of coating that contains polyurethane resins that is to be used as topcoat in atmospheric environments...
PAYNTGUARD ROOF is a solvent-based alkyd enamel finishing coat. It is formulated to give excellent durability, gloss, colour retention, good water-repellent properties, and double corrosion protection...
Enquiry Now
Reach out to us via our contact form below and we will get back to you as soon as possible!